• The reset button behind the door station, you will need to disassemble it.
• Initially unplug the AC adapter from your interior screen to work safely.

• Demonstrate the front face of your door station.
• Then remove the 2 screws that hold it on the wall:
• Gently remove the door station from the wall and make sure that the wires of the BUS1 and BUS2 are always connected.

• Connect the monitor to the power supply and wait for it to start.

• Make sure that passing a badge (regardless of the color) in front of the reader makes a beep or double beep of the door station.

Make sure you have all the badges nearby in order to program them.

• In the case of a new badge installation, please return the door station and press the RESET button for 5 seconds at the back of the door station.
• Street turntable will emit 6 bips short

Reminder: The passage of a badge must be done within 10 seconds after passing a previous badge. Otherwise, door station comes out of its programming mode.

If during the procedure, passing a badge emits 2 short beeps, it means that the door station has emerged from its programming mode. Please resume the procedure.

Pass the badges in the following order.

• Yellow badge:Street turntable emits 1 short beep
• Blue badge:Street turntable emits 1 short beep
• Red badge:the door station emits 1 long
• Blue badge:the door station emits 4 short bip
• Grey badge 1:Street turntable emits 1 short beep
• Grey badge 2:Street turntable emits 1 short beep
• Wait 10 seconds:Street turntable emits a long beep

Programming is complete. Only the passage of grey badges (users) will allow you to control your waste or portal.

• Pass one of the grey badge briefly in front of the door station.
• The door station will emit a short beep and the power supply of the electric striker will be carried out on terminals 7 and 8 of the door station.

• Pass one of the grey badge in front of the door station and leave it for 3 seconds
• The door station will emit a first beep and 2 beep after 3 seconds.
• The dry contact control for the engine will be carried out on terminals 5 and 6 of the street plate (a small click will be heard in the door station).

• Reinstall the door station on your wall in the opposite direction of disassembly.
• Do not forget the reinstallation of the silicone seal to make the back of your door station waterproof.

Procedure only valid if the administrator badges have been programmed. If this is not the case, please resume the procedure since Step 1

If during the procedure, passing a badge emits 2 short beeps, it means that the door station has emerged from its programming mode. Please resume the procedure.

Pass the badges in the following order.

• Blue badge:the door station emits 4 short bip
• Grey badge:Street turntable emits 1 short beep
• Wait 10 seconds:Street turntable emits a long beep
  

Procedure only valid if the administrator badges have been programmed and you have the user badge to delete. If this is not the case, please resume the procedure since Step 1

If during the procedure, passing a badge emits 2 short beeps, it means that the door station has emerged from its programming mode. Please resume the procedure.

Pass the badges in the following order.

• Red badge:the door station emits 4 short bip
• Grey badge to be deleted:Street turntable emits 1 short beep
• Wait 10 seconds:Street turntable emits a long beep
  

Procedure only valid if the administrator badges have been programmed. If this is not the case, please resume the procedure since Step 1.

If during the procedure, passing a badge emits 2 short beeps, it means that the door station has emerged from its programming mode. Please resume the procedure.

Pass the badges in the following order.

• Yellow badge:the door station emits 4 short bip
• Grey badge in your possession:the door station emits 1 short beep. All grey badges will be deleted.
• Wait 10 seconds:Street turntable emits a long beep