Before starting this tutorial, we invite you to take note of the fact that the code keyboard will take stand standby, and therefore will be released from the programming mode after 5s of inactivity.

Prepare the codes you want to program in advance and remember the steps to be taken before embarking on programming.

This code keyboard, resembling line to 114255, is not a code keyboard of our brand. It differs from our keyboard by its absence of mention A and B at its keys (* and # instead)

We will not be able to guarantee you compatibility with our electronic cards, nor that its access code setting process is the same as ours.

Press B and then 6 times button 9

The keyboard makes a long beep and turns on its green LED during the beep

This manipulation applies to a keyboard whose master code has never been changed. If your keyboard makes 10 quick beats to the composition of the last digit of the master code, it is because it is not good.

Go to Step 9 to find out the keyboard reset procedure.

Press the 2 button and then press B

The keyboard makes a long beep and turns on its green LED during the beep

Enter your access code (the code you want to order your engine) and press B.

The keyboard makes a beep and its green LED flashes twice.

Call your access code a second time and press B.

The keyboard makes two long beeps and lights on its green LED during the beeps.

Your access code is now programmed.

To check if everything went well and the keyboard has stored it well, dial the four digits of your access on the keyboard.

It will turn on its green LED for 2s if the code is good.

If the keyboard is four beep when composing the last digit of the access code, start the procedure again since step 1.

If you want to schedule a second access code on the keyboard (to have a code for pedestrian passage for example), resume the tutorial in step 1 and set an access code that does not start with the same number as the first you created.

For example, the first code created was 1234. The second code cannot be 1985. It will have to start with any number except 1.

Now that the keyboard transmits radio orders when composing your code, you need to record your code keyboard in your engine's electronic card for it to meet it.

This process differs depending on electronic cards.

Repair the card model you have to perform the right manipulations on it

Before starting handling at the electronic cards to program the keyboard on it, we invite you to note that electronic cards only remain in radio programming mode for 10s.

After launching the radio learning mode on the electronic card, quickly dial your code on your keyboard, otherwise the electronic card will leave radio learning mode without taking it into account.

To program a code for a total opening

• Press the RF2 button 3s
• While the red LED on the electronic card lights up, dial the four digits of your access code on the keyboard.
• The red LED flashes 3 times and then turns off

To program a code for partial opening

• Press the RF1 button 3s
• While the red LED on the electronic card lights up, dial the quattre numbers of your access code on the keyboard.
• The red LED flashes 3 times and then turns off

To program a code for a total opening

• Press the - key 3s (L1 lights up)
• Press SET once (L1 and L5 flash)
• Compose the four digits of your access on the keyboard
• All red lights turn on and go out.

To program a code for partial opening

• Press the - key 3s (L1 lights up)
• Press the + button on the card once (L2 turns on)
• Press SET once (L1 and L5 flash)
• Compose the four digits of your access on the keyboard
• All red lights turn on and go out

You can find the detailed tutorial on the programming of this map via the link below. In your case, the composition of the code on the keyboard replaces the key on the remote control.

Programming of remote controls on a CA2B9 card - Pedestrian/partial opening

To program a code for a total opening

• Press the - key 3s (L1 lights up)
• Press OK(L1 and L4 flashing) once
• Compose the four digits of your access on the keyboard
• All red lights turn on and go out.

To program a code for partial opening

• Press the - button 3s (L1 turns on).
• Press the + key on the card once (L2 turns on).
• Press OK once (L1 and L4 flash).
• Compose the four digits of your access on the keyboard.
• All red lights turn on and go out.

If you want to increase the security of the keyboard, you can change the master code that allows you to enter the keyboard settings.

Press B and then 6 times.

The keyboard makes a long beep and turns on its green LED during the beep.

Press the 1 button and then click B.

The keyboard makes a long beep and turns on its green LED during the beep.

Enter your master code (6-digit code) and press B.

The keyboard makes a beep and its green LED flashes twice.

Compose your master code a second time and press B.

The keyboard makes two long beeps and lights on its green LED during the beeps.

Note well in a corner this code that can serve you if one day you want to change an access code.

If you have lost your master code and you can no longer enter the keyboard settings

• Remove the keyboard from its wall mount by removing the screw from below.
• Open the code keyboard by unscrewing the 4 rear screws.

Remove a stack from the keyboard.

Press and hold the A key.

While retaining the A key, put the battery back into the keyboard.

Keep the A key down until you hear a long series of beeps.

Master code is reset and returns by default (999999)

The reset does not change access codes.

Have you entrusted the code to a person and you no longer want them to access your property?

For this, two possibilities are available to you

To change an access code, simply rewrite a new code starting with the same number instead. Take the tutorial from Step 1, and set a new access code starting with the same number as the one you no longer want to have (e.g. old code 1234, new code 1478)

This code change does not involve reprogramming the keyboard on the electronic card of the motorization.

The second solution is more restrictive. It consists of emptying the radio memory of your electronic motorization card so that it removes the keyboard from its authorized transmitters.

Be careful, the reset of the radio memory removes all recorded items, so including the remote controls you have in addition to the keyboard.

Removal of radio memory from a CA2B9 card